Tips on how to Replace Your GE Washer s Command Board
The control board is the central control for just about all of your GENERAL ELECTRIC washer? s functions. The switches, dials, and knobs most connect to the control board. If it shorts away or gets broken, your machine will certainly start to lose functionality or will certainly stop working totally. Models using a digital readout also can show an error computer code telling you whenever the control panel has stopped working. If you such as fixing your personal appliances, this can be a maintenance you can make yourself. Order replacement unit part #WH12X10468 with regard to most GE cleaner models. Then comply with these steps to be able to uninstall and exchange the old command board.
Unplug the washing machine.
This can be the first step to be able to any appliance repair project. Once you have discovered what? s incorrect with your washer, make sure an individual unplug it completely so you remain safe from electrical launch and shock.
<img width="341" src="https://www.pouted.com/wp-content/uploads/2018/01/Washing-machine-repairman-appliances-repair-technician.jpg">
Disassemble the washer.
Move the washer away from the wall. You simply need enough area to slide typically the top access panel back. If https://ulsterappliancerepair.com have room, attempt to pull typically the washer away coming from the wall because little as probable which means you don? t must detach the particular hoses or turn off water.
Take out the three anchoring screws along the back again edge of the top access section and the three screws along the particular back of the cut alongside the handle panel. Then you can certainly move the top screen an inch back again, which loosens the particular hold on the particular front trim piece. Carefully pry the trim clear of the tabs make that aside. Lift the top panel? h back edge up and then established the entire panel aside.
Remove the control screen next. To start, move out the cleaning agent drawer in the particular left-hand side and even depress the show in the back of the bathroom drawer in order to remove this entirely. Set this aside. Take away the twist next to typically the detergent drawer enclosure. Next, remove the particular screws along the back of the control panel gaming console. Also, pry way up the top advantage of the system to loosen the particular control panel. Hold onto the command panel and press the two locking an eye on the back of the gaming system inside the washing machine. Once it arrives free, don? t pull it aside or let it slide. Instead, tilt it down so that you can start off to unplug the wires.
You may need to remove all of typically the wire harnesses linked to the control panel. What you just have to perform is press straight down the tab on each of your plug. You put on? t have to be able to worry about blending them up in the course of reinstallation because every single plug has an unique shape. On the other hand, if you? re nervous about working together with wiring, take an image from multiple perspectives so you have got a visual guide of where each wire control should go.
Once the the control panel is entirely detached in the washer, move it to a work surface. This is the part that homes the control board.
Remove the outdated control board.
Depart the control -panel face down. Remove the screws alongside the perimeter from the control board. There ought to be four. Also, depress the locking tabs along the edge with the control table nearest the winding edge of the control panel. These can be difficult to reach, so use a flathead screwdriver to move typically the tabs. Pull the particular control board away and shift the control panel away.
Flip the management board over. Acquire a picture associated with all the control keys in the front part in the control panel so you have a visual guide during reinstallation. Then start off removing all the buttons and assemblies thus you can maneuver them over in order to the new part. They should be relatively loose, thus don? t use too much pressure on the slim plastic parts.
Install the modern control table.
Prior to deciding to put the new control plank part within the control panel console, mount all of the buttons you eliminated from the outdated part. The lengthier assemblies will generally have hooks that really must be slid into the cutouts on the particular control board in order to provide extra balance. Make sure every of the control keys is installed so that they match the picture guide.
Once typically the buttons are in place, pick upwards the control table and tilt this so it? s practically perpendicular to the particular ground. Fall into line typically the control board? s shaft using the pit in the control panel. As you perform so, wiggle the knob a lttle bit therefore the shaft lines up with the hole and snaps entirely into place. The the control panel helps hold the buttons inside place, but in case you tilt the control board also far forward throughout this step, some associated with the buttons may come loose. in case anything falls out of place, just reinsert the hooks and attempt again.
Once the control board base is at place, thoroughly keep both parts held together plus set the handle panel face lower. Now you can lock both pieces together by gently pressing the three securing tabs into spot and retightening the four screws close to the edge with the control board.
Reassemble the washer.
Very first, orient the control board assembly beside the top of the front regarding the washer so the curved edge is usually closest to the machine. Start plugging the wire harnesses into the command board by using the picture guide or by matching every wire harness to the correct plug.
Next, tilt typically the control panel regress to something easier so it? s i9000 flush with typically the top front regarding the washer, and ensure none of the particular wires get pinched. Slide the dividers along the bottom into the slot machines on the right part, and snap typically the control panel into spot. From then on, retighten the particular screw that sits down beside the cleaning soap drawer housing. In addition, retighten the screws across the back of the control panel. In that case slide the cleaning agent drawer into spot and reattach typically the top access screen. If you look at the bottom part with the top gain access to panel, you? ll notice slots regarding the circular pins along the train. The pins need to go through the larger end of the particular cutout and so the panel lies flat and even then, when a person slide the section forward, lock in to place against the particular smaller area of the particular cutout. This element can be challenging, so a visible guide like in the end regarding this video might help.
To get this done, arranged the top accessibility panel carefully on top of the frame and the pins. It ought to hand approximately a great inch off the particular back. Before an individual slide the section forward, press the particular trim into place on three securing tabs. Then go the panel forward and add back all six anchoring screws to hold this set up.
Push your washer back into place and connector it in. Comply with the guide of which came with typically the control board to be able to program the machine. Each model provides a slightly different step. As soon as your washer provides been programmed, that? s all set to begin a new routine.