What Experts From The Field Want You To Be Able To
Peugeot 208 Key Replacement
Peugeot 208 key replacement should be left to auto locksmiths with experience who have the appropriate equipment and know-how. They can create and program keys more quickly and at a lower cost than a dealership.
If the key fob has stopped locking or unlocking your doors, it is likely due to a dead battery in the coin. There are other possibilities that the key is malfunctioning.
Dead Coin Battery
A dead battery in the coin compartment will stop your Peugeot 208 from locking or unlocking and will not start the engine. If this is the scenario, you'll need make use of the backup starting procedure that is described in the owner's manual of your vehicle.
The spark plugs can also be worn out. The spark plugs light the fuel to start the engine. peugeot replacement key fob G28 have a limited life span. If they are not used enough, they will eventually fail.
There is an easy solution to this problem. Verify the voltage of your battery using a multimeter. If it is below 11.5 volts it is time to replace it. It is also essential to clean the contacts of the battery in the event that it is damaged by corrosion. You can do this by lifting the rubber covers that protect the two terminals of the battery and using wire brushes to clean any corroded areas of the battery. Then, you must reconnect the positive and negative pole cables.
Water Damage
If your 208 won't turn on and the battery is not flat then you should check whether the spark plugs are in good working order. You may find that they are dirty and do not spark. This can be fixed by cleaning the spark plugs in the workshop.
Peugeot automobiles use transponder keys that works with the car's ignition system. This ensures that only a valid key is able to turn the engine. If the chip inside the Peugeot key is damaged, it won't send the correct signal to the vehicle.
Water damage is a frequent cause of this problem. This is especially prevalent in colder climates where the vehicle may have been exposed to snow or rain. If this is the case, you should get in touch with a reputable locksmith who will have all of the tools and equipment needed to modify the new key. They'll also have the latest technology and equipment required to create a Peugeot smart key. The process shouldn't take more than 15 minutes.
Contacts for the battery that are defective
Peugeot replaced the transponder chips by introducing a new type that uses electronic components that are mounted on a circuit board. This new system works well when it's brand new but over time the circuit boards begin to wear out and stop functioning properly.
This could prevent the immobiliser from triggering so that the vehicle won't start. Contact a Peugeot specialist or a locksmith, if this is the case.
Another common issue is when the battery in the key fob gets depleted, which causes the key blade to stop feeding into the lock. A locksmith in your car will replace the battery and then cut a new blade for you. This is a simple solution.
Faulty Receiver Module
If your Peugeot key fob stopped working after dropping it on the floor, being exposed to a sudden downpour or accidentally washing it the wrong way, it could be due to a malfunctioning receiver module. The receiver module is responsible for transmitting radio signals to the onboard computer that regulates the central locking system of your Peugeot vehicle.
The rubber seals on the key fob keep water from reaching its electronic chip. However, prolonged exposure to water could be able to penetrate these seals and cause damage to the chip. Submerging the key fob into the ocean at the beach or throwing it into the pool could be particularly damaging due to the high salt content.
The module needs to be replaced if your Peugeot spare key no longer works. This can only be done by a skilled auto locksmith or Peugeot specialist. Like other automobiles, Peugeot keys are protected by an immobilizer that is unique and requires the right coding to begin the engine. It is for this reason that you should only rely on the Peugeot locksmith to design and program the replacement.
Computer with a problem on board
The computer on board in your Peugeot is responsible for a number of the systems inside your vehicle, from power windows to airbags. If something goes wrong with these systems, it will usually show a code that identifies the issue. This code is saved in the system and will remain there until the issue is fixed. In most cases, this will require the on-board computer being replaced.
The most typical reason for the warning light for the airbag to turn on is corrosion or loose connections within the sensor. This could be due to wear and tear, aging or exposure to salt and moisture. This problem should be taken care of as soon as you can, since an airbag that's malfunctioning could pose a risk in the event in the event of an accident.
If your Peugeot is showing a card detected as not present error, then the battery inside the key fob could be weak or dead. This could prevent the key fob from sending a signal that disarms your vehicle's standard immobilizer. Try this by pressing the unlock key on the fob's key, then trying to start your car. If it doesn't work it is because the battery of the key has to be replaced.