What Makes The Peugeot Keys So Effective During COVID-19
Peugeot 208 Key Replacement
It is best to leave the replacement of Peugeot keys for 208 to auto locksmiths with the equipment and expertise. They can create and program new keys much quicker than a dealership and at a lower price.
A dead battery for your coin is the most likely cause the reason your key-fob stops locking or unlocking the doors. There are other reasons why the key might be malfunctioning.
Dead Coin Battery
A dead coin battery can prevent your Peugeot 208 from locking or unlocking and cannot start the engine. In this scenario you'll have to make use of the alternative method for starting that is described in the owner's manual.
The spark plugs can also be worn out. The spark plugs light the fuel to start the engine. They are only able to last for a short time. If they're not used enough to last, they'll eventually fail.
There is a straightforward solution to this issue. The best solution is to determine the voltage of your car battery with a multimeter. If the voltage is less than 11,5 volts, it's time to replace it. If the battery has corrosion it is crucial to clean its contacts. This can be done by removing the rubber cover from the two battery terminals and then using a wirebrush to clean any corroded battery parts. Then, you should connect the cables that connect the positive and negative poles.
Water Damage
If your 208 won't start and the battery is not flat then you should check that the spark plugs are in good working order. It could be that they are simply too dirty and do not spark. This can be easily corrected by cleaning the spark plugs in a workshop.
Peugeot cars use a key with a transponder compatible with the immobiliser. This ensures that only a valid key is able to turn the engine. If the chip inside the Peugeot key is damaged, it won't transmit the proper signal to the vehicle.
Water damage is a frequent cause of this issue. This is particularly common in colder climates, as the vehicle could have been exposed to snow or rain. If this is the case, you should seek out a reputable auto locksmith who has all the equipment and tools needed to change the key's programming. They will also have all the latest technology and equipment required to create a Peugeot smart key. The process shouldn't take longer than 15 minutes.
Contacts with the battery may be damaged.
Peugeot changed from the old carbon-encased transponder chips to a brand new type of chip that relies on electronic components on a circuit board. The new system is excellent in its initial state, but the circuit boards deteriorate over time and stop working properly.
This could prevent the immobiliser chip from triggering the immobiliser chip, causing your car not to start. Contact an Peugeot specialist or a locksmith if this is the case.
The most frequent issue is when the battery inside the key fob starts to die. This causes the blade of the key to stop feeding into your lock. A locksmith from your car will replace the battery and cut a new blade for you. This is a simple solution.
Faulty Receiver Module
If your Peugeot key fob stopped working after dropping it on the floor, being exposed to a sudden rain or accidently washing it, it could be due to a defective receiver module. The receiver is responsible for sending radio frequency signals to an on-board computer that controls the central locking system within your Peugeot vehicle.
The key fob itself has rubber seals that prevent water from reaching the electronic chip inside. However prolonged exposure to water can break through these seals, causing damage to the chip. Submerging the key fob into the ocean at the beach or throwing it into the water can be especially damaging because of the high salt content.
The module needs to be replaced if your Peugeot spare key does not work anymore. This can only be done by a skilled auto locksmith or Peugeot specialist. Peugeot keys unlike other automobiles, are protected by an immobilizer system. peugeot spare key requires the proper code to begin the car. This is why it is imperative that you should only rely on a Peugeot locksmith to design and program a replacement.
Faulty on-Board computer
The on-board computer inside your Peugeot is responsible for many of the systems inside your car, ranging from airbags to power windows. The on-board computer displays the code when something goes wrong. This code is saved in the system and stays there until the problem is solved. Most often, this involves replacing the on-board computer.
The most typical reason for the airbag warning light to turn on is corrosion or loose connections within the sensor. This can be caused by wear and tear, aging or exposure to salt and moisture. This problem should be dealt with as soon as you can, as an airbag that is malfunctioning could pose danger in the event of an accident.
If you see an error message stating that the card is not found on your Peugeot, the key battery inside the key fob could be weak or dead. This can prevent the key fob from sending a signal to disable the standard immobilizer in your vehicle. Test this by pressing the unlock button on the fob's key and then trying to start your car. If this does not work, the key battery needs to be replaced.