How Peugeot Keys Was Able To Become The No.1 Trend On Social Media
Peugeot 208 Key Replacement
It is better to leave the replacement of Peugeot 208 keys to auto locksmiths who have the necessary equipment and technical expertise. They can program and create keys faster and less expensive than dealers.
If the key fob stopped locking or unlocking your doors, it is likely due to a dead battery in the coin. There are other reasons that the key could be malfunctioning.
Dead Coin Battery
A dead battery can stop your Peugeot 208 from locking and unlocking, and also preventing it from starting the engine. If this is the situation, you'll need use the backup starting method which is explained in the owner's manual of your vehicle.
The spark plugs can also be worn out. Spark plugs are what ignite the fuel to start the engine. However, they have a limited lifespan. If they aren't used enough they will eventually fail.
There is a simple solution for this issue. Verify the voltage of your battery using a multimeter. If it's lower than 11.5 volts it is time to replace it. It is also necessary to clean the contacts of the battery in the event that it is damaged by corrosion. This can be done by lifting the rubber covers that protect both battery terminals and using wire brushes to clean any corroded components of the battery. Then, reconnect the cables that connect the positive and negative poles.
Water Damage
If your 208 won't start and the battery isn't flat then you should check whether the spark plugs work. It could be that they are dirty and do not spark. The spark plugs can be cleaned in the workshop.
Peugeot cars use a key with a transponder that is compatible with the immobiliser. This ensures that only the correct key is able to turn the engine. If the chip inside the Peugeot key is damaged, it won't send the correct signal to the vehicle.
This is a common problem that can be caused by water damage. This is a typical issue in more cold climates where the car has been exposed to rain or snow. If this is the case, you should get in touch with a reputable locksmith who has all the equipment and tools needed to change the key's programming. They will also have the most up-to-date technological know-how and machinery required to make the Peugeot 208 smart key. The process should take no more than 15 minutes.
Faulty Battery Contacts
Peugeot changed from the old carbon encased transponder chips to an entirely new type of chip that incorporates electronic components on a circuit board. The new system works great in its initial state, but the circuit boards degrade over time and cease to function properly.
This can prevent the immobiliser chip from triggering, so your car won't start. Contact a Peugeot specialist or a locksmith, if this is the situation.
Another common issue is when the key fob battery gets depleted, which causes the blade of the key to stop feeding into the lock. A locksmith from your car will replace the battery and then cut a fresh blade for you. This is a simple solution.
Faulty Receiver Module
If your Peugeot key fob has stopped working after dropping it on the floor, being exposed to a sudden downpour or accidently washing it may be due a malfunctioning receiver module. The receiver module is responsible for transmitting radio frequencies to the onboard computer which regulates the central locking system of your Peugeot vehicle.
Rubber seals on the key fob block water from reaching its electronic chip. The chip can be damaged by water in the event that it is exposed water for a prolonged period of time. Submerging the key fob into sea water at the beach or throwing it into the pool could be particularly damaging due to the high salt content.
If your Peugeot spare key fob doesn't work, you'll need to have the module replaced. This can only by done by a Peugeot specialist or a professional auto locksmith. peugeot 307 key fob like other cars are protected by an immobilizer system. This requires the proper code to begin the car. This is why you should be able to trust a professional Peugeot locksmith to take on the job of programming and creating an alternative.
Computers with faulty on-board computers
The computer on board of your Peugeot is responsible for a variety of functions in your car including power windows and airbags. If something is wrong with these systems, it'll typically display a code that identifies the problem. This code will be saved within the system until the issue is resolved. This will often require the on-board computers to be replaced.
The most common cause of the airbag warning light to come on is corroded or loose connections within the sensor. It can be due to wear and tear, aging or exposure to salt and moisture. It is crucial to get this issue addressed as soon as you can, as an airbag that is malfunctioning can be dangerous in the event an accident.
If your Peugeot is showing a card detected as not present error then the key battery inside the key fob may be dead or weak. This can prevent the key fob from sending a signal that disarms your vehicle's immobilizer. Test this by pressing the unlock button on the key fob, and then trying to start your car. If this does not work, then the key battery must be replaced.