20 Important Questions To Be Asking About Fiat Panda Key Fob Replacement Before You Buy Fiat Panda Key Fob Replacement

Reasons Your Fiat 500 Key Fob Won't Work

A key fob from Fiat 500 is a great way to unlock the doors and start the car. There are a myriad of reasons why the key fob might stop functioning. These include a dead battery water damage, receiver module issues, and interference.

This listing is for a NEW replacement Fiat Flip Key Remote that is similar to the Ilco brand. Read A great deal more has to be professionally programmed (click here to search for local locksmiths in the automotive industry). It comes with lock, unlock and trunk buttons.

Dead Coin Battery

A dead battery is the most common reason for your 500 key fob being inoperative. Modern key fobs have an operating range that is limited and must be within just a few inches of the vehicle to work. If you're far away from your vehicle when you press the key fob button, the car will not respond, and will display the "Key Fob Not Detected" message in the instrument cluster.

If this happens you need to replace the battery of your coin-cell (Part Number CR2032) by a fresh one of a trusted brand like Panasonic Duracell or Energizer. You can find them in your local hardware store, or on the internet.

You can test the battery of your coin-cell by pressing the buttons while you're standing close to your Fiat 500. The parking lights will flash and the key fob should operate the lock and unlock switch.

If your key fob isn't working after replacing the battery, there could be water damage that is preventing it from interacting with the module in your vehicle. Water damage can happen in a number of ways, ranging from small splashes to submerging your fob in salt water at the beach. If you suspect that your fob has been exposed to water, you can place it in a bag of rice to draw out the moisture. If this doesn't work, you will need to have the fob replaced by an auto locksmith or a dealer.

Water Damage

The fob does have rubber seals that keep water from the electronic chip inside the device, submerging it into the ocean or washing it in a machine could cause water damage. Saltwater is especially dangerous to the circuit board of the fob and can cause it to short out and eventually die. The fob getting wet is not an option but if you accidentally drop it in an empty cup of water, or don't remember to take it out of your pants pocket prior to running the washing machine do not give up hope.

Remove the battery first. Clean the electronic chip using isopropyl alcohol or a similar product and then dry it completely before replacing the battery. Check the fob to verify if it's working. If the key does not function then it might need to be reset. This is typically handled by a dealer or professional auto locksmith.

If the key is newer and has not been programmed to your car It is likely that it needs to be replaced completely. This is a simple procedure that can be carried out by a professional locksmith for automotive use. The locksmith will need to cut the key to match the ignition in your vehicle. They will also need to reprogram the fob in the car's system. This is a cost-effective and fast process that can be completed in the same day.

Receiver Module Issues

Your 500 key fob may be inoperable because it's out of range. The remote has a range of 30 feet, so when you're too far from your car it won't be able to respond to your commands. It is possible to solve this issue by moving the remote closer to your car until it responds.

If your fob isn't working after you replace the coin battery, also called a "button", "watch" or "button" it could be a problem with the circuit board inside. Reprogramming the fob typically resolves the issue. The instructions are available for the majority of vehicles on YouTube or in the owner's guide.

You may have to replace the metal retaining clips that keep the battery of your coin in place. If they loose tension, it could prevent your coin battery from being properly seated, causing your remote to malfunction.

In rare cases the fob might become desync'd with your vehicle due to software problems or hardware issues. This can cause a major trouble, but you could often fix this by visiting a local dealer or auto locksmith to reprogram your fob. In some cases the software may require reinstallation to your body control modules.

Interference

In addition to a dead coin battery the key fob could not be able to receive or transmit an signal due to interference. This could happen when the key fob is in close proximity to a radio transmitter, such as a cell phone or radar detector. Other reasons why the key fob might not work include a poor connection to the buttons or the internal chip, or water damage.

If your key fob suddenly stopped working, or you've tried everything at home to resolve it (e.g. battery replacement, reprogramming and using the spare key fob, it could have a damaged receiver module on your 500. The receiver module is located under the dash and receives the radio frequency signals from the key fob. It converts the signals into electronic commands, which are then processed by the vehicle.

There is a straightforward method to reset the 500's internal system including the keyfob. Disconnect the battery 12 volt for about 15 minutes, by removing the negative cable and then the positive cable. Then, reconnect the battery. This will remove any remaining electricity, and allow you to restart the computer in your car. This can help get your key fob working again. If the issue persists, you should consult an expert technician. They will be able to determine the root of any issues.

Edit
Pub: 26 Mar 2024 21:31 UTC
Views: 22