Tips on how to Replace Your GENERAL ELECTRIC Washer s Handle Board

The control panel is the key control for all of your GENERAL ELECTRIC washer? s functions. The switches, calls, and knobs almost all connect to the control board. In the event that it shorts away or gets ruined, your machine may start to drop functionality or will stop working completely. Models with an electronic readout could also exhibit an error signal telling you when the control table has stopped doing work. If you such as fixing your personal appliances, it is a fix you can create yourself. Order alternative part #WH12X10468 for most GE washer models. Then adhere to these steps to be able to uninstall and change the old management board.

Unplug the washing machine.
This is the first step to be able to any appliance repair project. After getting determined what? s incorrect with your washing machine, make sure an individual unplug it entirely so you stay safe from electrical release and shock.

Take apart the washer.
Pull the washer away from the wall. You just need enough place to slide typically the top access -panel back. If an individual have room, attempt to pull the particular washer away coming from the wall since little as achievable so that you don? t need to detach typically the hoses or change off the water.

Get rid of the three screws along the rear edge of the particular top access -panel and the about three screws along the back side of the trim beside the control panel. Then you could pull the top panel an inch back, which loosens the particular hold on typically the front trim piece. Carefully pry the trim without any the particular tabs make that aside. Lift the particular top panel? s back edge upwards and then fixed the full panel besides.

Take away the control section next. To start out, draw out the detergent drawer in typically the left-hand side and even depress the clip behind the cabinet to help you remove this entirely. Set that aside. Eliminate the mess next to typically the detergent drawer casing. Next, remove the particular screws along the particular back of the particular control panel gaming console. Also, pry way up the top border of the console to loosen the particular control panel. Carry onto the management panel and push the two fastening tabs on the back again of the system inside the washing machine. Once it will come free, don? to pull it aside or allow it slide. Instead, tilt that down in order to begin to unplug typically the wires.

You will need to remove all of the particular wire harnesses linked to the control panel. All you have to perform is press down the tab to each plug. You add? t have to be able to worry about mixing up them up during reinstallation because each plug has a good unique shape. Nevertheless, if you? re stressed about working using wiring, take an image from multiple perspectives so you have a visual guide of where each wire harness should go.

Once the control panel is totally detached from your machine, move it to be able to a work area. This is the part that homes the control panel.

Remove the aged control board.
Leave the control panel face down. Get https://ulsterappliancerepair.com of the screws along the perimeter in the control board. There should be four. Also, depress the locking tabs along the advantage in the control plank closest to the winding edge of the particular control panel. These can be difficult to reach, so use a flathead electric screwdriver to move the particular tabs. Pull the particular control board out there and shift the control panel apart.

Flip the management board over. Consider a picture of all the buttons with the front part from the control panel which means you have a visual guide throughout reinstallation. Then begin removing all the switches and assemblies therefore you can shift them over to be able to the new component. They should become relatively loose, thus don? t implement too much force on the thin plastic parts.

Install the brand new control panel.
Before you put the particular new control plank part inside the control panel console, install all of typically the buttons you removed from the old part. The extended assemblies will usually have hooks that really must be slid into the cutouts on the particular control board to provide extra stableness. Make sure each of the buttons is installed so that they match the photo guide.

<img width="462" src="https://thumbs.dreamstime.com/b/repairman-posing-next-to-washing-machine-19517509.jpg">

Once typically the buttons are within place, pick way up the control panel and tilt it so it? s nearly perpendicular to typically the ground. Line up typically the control board? t shaft together with the hole in the control panel. As you do so, wiggle typically the knob a bit and so the shaft aligns with the opening and snaps totally into place. The particular control panel helps carry the buttons in place, but in case you tilt the control board as well far forward during this step, some of the buttons may come loose. in the event that anything falls misplaced, just reinsert the particular hooks and try out again.

Once the control board base is at place, carefully keep both pieces held together in addition to set the management panel face along. Now you can lock both the items together by gently pressing three locking tabs into place and retightening the four screws about the edge of the control board.

Reassemble the washer.
First, orient the control board assembly next to the top involving the front involving the washer therefore the curved edge will be closest to the machine. Start inserting the wire harnesses into the handle board by pursuing the style guide or even by matching every single wire harness to the correct put.

Next, tilt the particular control panel backup so it? s flush with the particular top front of the washer, and make sure none of the particular wires get pinched. Slide the tabs along the bottom part into the slot machines on the right corner, and snap the the control panel into spot. There after, retighten the particular screw that sits down beside the detergent drawer housing. Also, retighten the screws along the back associated with the the control panel. Then slide the cleaning agent drawer into location and reattach the top access screen. If you seem at the base from the top gain access to panel, you? ll notice slots with regard to the circular pins along the train. The pins need to go through the larger end of the particular cutout therefore the section lies flat and then, when you slide the -panel forward, lock straight into place against the smaller percentage of the cutout. This component can be challenging, so a visual guide like in the end of this video may possibly help.

To achieve this, established the top gain access to panel carefully together with the frame plus the pins. It should hand approximately a great inch off the particular back. Before an individual slide the screen forward, press the trim into place on three fastening tabs. Then go the panel forwards and add back again all six screws to hold this in position.

Push the washer back straight into place and connector it in. Comply with the guide that came with the control board to program the washer. Each model has a different step. When your washer offers been programmed, that? s willing to start a new cycle.

Edit

Pub: 12 Feb 2023 10:08 UTC

Views: 33