Why Your AC Unit is Blowing Warm Air on a 100 Degree Day
Why Your AC Unit is Blowing Warm Air on a 100 Degree Day
Why Your AC Unit is Blowing Warm Air on a 100 Degree Day
Glendale, CA summers punish air conditioners. Asphalt bakes along Brand Boulevard. Attics in Rossmoyne and Adams Hill hit 140 to 160 degrees by midafternoon. Santa Ana winds load outdoor condenser coils with grit near the Verdugo Mountains and Glenoaks Canyon. When the thermostat calls for cooling and the vents push warm air, the system is telling a clear story. It is either starved for refrigerant, blocked for airflow, or stuck behind an electrical fault. In Glendale AC repair work, those three buckets explain most no-cool calls during a 100-degree day.
Green Planet Heating and Air services homes and small businesses across 91201, 91202, 91203, 91204, 91205, 91206, 91207, 91208, and 91210. The team is locally based near the Americana at Brand and Glendale Galleria. Trucks roll daily through Verdugo Woodlands, Chevy Chase Canyon, Riverside Rancho, Brockmont, Montecito Park, and the apartments near Brand Park and the Alex Theatre. The field notes below come from those blocks, backed by EPA certified technicians and CSLB licensing. They speak to why warm air happens, how to confirm it fast, and what a correct fix looks like under California Title 24 and SEER2 practice.
How a Glendale System Loses Its Cool When It Is 100 Degrees
A central air conditioner moves heat. The refrigerant absorbs heat in the evaporator coil at the air handler and rejects it through the condenser coil outdoors. The compressor drives the cycle. The metering device, often a thermostatic expansion valve, controls superheat at the evaporator. Airflow across the indoor coil must be correct, around 350 to 450 CFM per ton in Glendale’s dry heat. On a 100-degree day, load spikes, attic ambient climbs, and condensing temperatures soar. Any weakness shows fast.
Warm air at the supply vents comes from a break in that chain. A short list covers the bulk of cases in Los Angeles County during heat spikes. A blown start capacitor leaves the compressor stalled while the outdoor fan spins. A failed contactor starves the compressor of power. A frozen evaporator coil blocks heat exchange and the blower pushes air around ice. A clogged filter or crushed return raises static pressure and cuts CFM to a trickle. A refrigerant leak reduces mass flow, dropping suction pressure and coil temperature, which first ices and later warms as the compressor overheats or trips on safety. A thermostat misread, often in a sunlit hallway near a south-facing window, fools a system into short cycling.
Green Planet’s Glendale AC repair data shows three fast movers during 100-degree weeks: blown capacitors, dirty condenser coils, and low refrigerant charge. All three are preventable with a real maintenance plan under a 26-point check, and all three respond well to a same-day truck roll with stocked parts.
Electrical Faults That Make Vents Blow Warm
When the system hums but cooling stalls, start with the electrical path. The service disconnect at the condenser, the contactor, the start or run capacitor, and the compressor windings form the core. Capacitors dry out under heat. In Glendale, outdoor enclosures sit on patios in Riverside Rancho and balconies near Brand Boulevard with metal boxes exposed to direct sun. Case temperatures climb. A capacitor that drifted from 45 µF to 30 µF may let a fan motor spin yet leave the compressor locked. The indoor blower moves air, but the loop does not move heat. The result is warm supply air within minutes.
Technicians test microfarads under load and swap a like-for-like rated part. Green Planet keeps universal start capacitors and contactors on every service truck so most Glendale AC repair calls finish in one visit. A welded contactor is another heat-day classic. The fan runs without compression, or the compressor cycles erratically. Voltage drop testing and visual arcing marks tell the story. Replacing the contactor, checking spade terminal fit, and verifying proper coil voltage stabilizes the circuit.
Thermostat logic adds a layer. A misconfigured smart thermostat can call only for fan, not for cooling. A C-wire dropout can reboot the stat during peak draw. Glendale apartments with shared corridors near the Glendale Central Library sometimes mount thermostats where radiant heat skews readings. Proper stat placement and mode verification prevent phantom calls that feel like warm air with the system “running.”
Airflow and Duct Problems That Break Heat Exchange
Airflow equals capacity. If the evaporator coil cannot see enough CFM, it gets too cold and ices. If it sees bypass air from disconnected ducts, the air at the registers feels warm or neutral. Glendale homes in Rossmoyne and Verdugo Woodlands often have partial returns and undersized filter racks inherited from older gas furnace cabinets. A 3-ton system wants roughly 1,200 to 1,350 CFM in this climate. A choked MERV 13 filter on a single 16 x 25 rack can set static pressure above 0.8 in. W.c. The blower ramps to maximum on a variable speed air handler yet still fails to move enough air through the evaporator. Ice forms. Then the blower circulates around a block of ice that absorbs little heat. Vents blow warm or even hotter, since some duct runs soak in 140-degree attics above Adams Hill.
Green Planet techs measure total external static, plot fan curves, and correct restrictions. The fix can be as simple as a fresh MERV 11 to MERV 13 filter and a coil wash or as involved as cutting in an additional return and sealing duct leakage with mastic. Glendale’s wildfire seasons push ash into outdoor coils. Santa Ana winds drive dust into soffit vents. Both increase static pressure inside and condensing temperatures outside. Precision tune-ups include coil cleaning with the right pH solution and low-pressure rinse to protect fin geometry, restoring heat transfer and cutting head pressure.
Refrigerant Circuit Faults Under Valley Heat
A sealed refrigerant circuit should not lose charge. If it does, vents first feel weakly cool, then neutral, then warm as the compressor overheats. On 100-degree days, the effect accelerates. Common leak points include flare fittings on ductless linesets in Chevy Chase Canyon homes, Schrader cores at service ports on older Goodman and York condensers, and evaporator coil hairlines on aging Lennox and Rheem equipment. Modern variable speed heat pumps from Daikin and Mitsubishi Electric show different symptoms, sometimes ramping to high speed to mask a small leak, then tripping a protection code.
Proper repair follows EPA Section 608 protocols. A Glendale ac repair done right recovers refrigerant, pressure tests with dry nitrogen to 300 to 400 psi depending on coil rating, sprays bubbles or uses an electronic leak detector at the TXV, U-bends, and braze joints, then repairs with nitrogen flowing through the tubing to prevent oxidation. After repair, evacuation pulls to at least 300 to 500 microns with a rise test to confirm a clean, dry system. A filter drier is replaced or added. Charge is set by superheat or subcooling against manufacturer tables, factoring Glendale’s high ambient. For R-410A split systems, subcooling often targets 8 to 12 degrees in these conditions. A correct charge changes vent temperature differences from 2 to 5 degrees back up to 16 to 22 degrees in minutes under steady state.
Many Glendale homes now run variable speed heat pumps or dual-fuel systems. On these, a stuck reversing valve can also cause warm air in cooling mode. If the valve fails to shift or bleeds, the system will not reject heat. Technicians test coil energizing, measure line temperatures, and confirm mode. When the reversing valve sticks mechanically, replacement is the fix, followed by evacuation and recharging under SEER2 field practices.
Frozen Evaporator Coils in Glendale Homes
Frozen coils are common during heat waves for two reasons that seem at odds. Low charge drops suction pressure and coil temperature, which ices fast. Restricted airflow lets the coil temperature plunge below freezing even with proper charge. Both starve the coil of heat to absorb. Homeowners in 91206 and 91208 often report warm air in late afternoon after the system ran fine at noon. That pattern points to icing that builds during peak load and then melts once the system shuts off, leaving a pan full of water and a clogged condensate line threat.
A field check uses temperature split and visual inspection. A normal split in Glendale is 18 to 22 degrees with indoor at 75 and outdoor at 100. If split is 6 to 10 degrees and the suction line is not cold, charge may be low. If the return filter is packed and the supply registers wheeze, airflow is the first fix. Technicians will also check the TXV sensing bulb placement and insulation, since a loose bulb on the suction line drives erratic superheat and icing. Clearing the condensate line prevents water damage in Adams Hill bungalows where air handlers sit over plaster ceilings. Green Planet’s tune-ups clear condensate lines with nitrogen and treat pans, since Verdugo Woodlands homes with leafy yards see algae growth that plugs traps.
Why Glendale’s Microclimate Pushes Systems to the Edge
Topography matters. Chevy Chase Canyon and Brockmont see evening downdrafts that cool air quickly outdoors while attics stay hot. This thermal lag strains systems during the dinner hour. Riverside Rancho sits near the Los Angeles River channel with higher dust load during Santa Ana events. Brand Boulevard corridors trap radiant heat and reflect it into apartments, raising interior loads. All of this affects condensing temperature, duct loss, return air temperature, and sensible versus latent loads. Wildfire smoke adds fine particulates that clog MERV 13 filters faster than expected. Green Planet adjusts maintenance schedules in Glendale based on these swings. Many homes benefit from mid-season coil cleaning, not only a spring tune-up, during years with heavy smoke.
California Title 24 and Energy Star guidance push higher efficiency, which helps Glendale homes. SEER2 ratings assume realistic external static. If ducts are undersized or leaky, actual field efficiency drops. Proper commissioning, with static readings, airflow set, and charge dialed in, returns comfort and lowers bills along Brand Park or near Forest Lawn Memorial Park homes that see long daily sun exposure. Smart thermostats, from Honeywell Home to advanced OEM controls, help stage equipment and hold tighter setpoints, but they must be programmed for Glendale’s climate cycle and the specific appliance type, whether a Carrier two-stage condenser or a Mitsubishi Electric Mr. Slim mini-split.
What the Warm Air Means by Equipment Type
Central air conditioners with single-stage compressors give clear symptoms. If the outdoor unit runs and the indoor air is warm, check the compressor. If only the fan turns, suspect the start capacitor or contactor. Measure amperage. A spiking inrush with no sustained run is a capacitor flag. If both indoor and outdoor units run yet vents are warm, check charge and coil condition.
Ductless mini-splits from Daikin, Mitsubishi Electric, and Fujitsu use inverter-driven compressors. They modulate and can mask small faults. Warm air at a wall cassette in a Chevy Chase Canyon living room can point to a refrigerant leak at the flare or a dirty outdoor coil mounted on a side yard rack. Fan coils sense coil temperature; if they never reach cooling range, the head will blow tepid air on low. These systems often throw diagnostic codes. Reading manufacturer data and line temperatures is faster than guesswork. Proper torque on flares, Nylog seal, and pressure testing prevents repeat leaks.
Variable speed heat pumps in dual-fuel systems can default to heat-only if the reversing valve does not energize. Glendale homeowners sometimes set smart thermostats to auto-changeover with narrow deadbands. On a day that starts cool and spikes hot, the system may pinball between heat and cool. Widening the deadband and confirming mode lockout fixes a surprising number of warm-air calls that sound serious at first.
Indoor Air Quality Factors That Trick the Senses
During 100-degree events, return air temperature spikes. If filters clog, smoke and dust push past with bypass, and odors build. Air that is technically cooling can feel warm if humidity rises and airflow drops. While Glendale is dry compared to coastal Los Feliz and Atwater Village, microbursts and monsoon moisture can raise indoor humidity. A blower on low speed with a packed MERV 13 filter can make a 70-degree supply feel muggy and stale, which homeowners describe as warm. Green Planet checks blower speeds, verifies duct sealing in attic chases, and chooses filter ratings that balance capture with airflow. For wildfire season, MERV 11 with increased filter area can beat a tight MERV 13 in a too-small rack.
What a Proper Glendale Diagnosis Looks Like
A thorough HVAC repair Glendale visit starts with a short interview. How long has the warm air issue lasted, and does it worsen in late afternoon. Where is the thermostat, and does sun hit it. Was any work done on electrical or remodeling that may have affected returns or attic ducts in the past year. Those answers focus the test plan.
Next comes measurement. Static pressure across the air handler. Supply and return temperatures. Suction and liquid line pressures, with superheat and subcooling. Compressor amperage and capacitor microfarads. Contactor condition and voltage. Filter condition and coil cleanliness. Condensate line flow. Only then does the repair begin. Swapping parts blind often misses paired faults, like a failing TXV that cooks a new compressor. In Glendale, where attics torch systems, a patient test saves time and money.
Green Planet technicians are trained on Carrier, Trane, Lennox, Rheem, Goodman, York, American Standard, and high-end systems from Daikin, Mitsubishi Electric, Fujitsu, Bosch, and Honeywell Home controls. They carry OEM-grade parts when needed and install to manufacturer specs. That protects warranties and holds performance through peak heat. The company is an Energy Star Partner, Google Guaranteed, and provides free estimates on new installs when repair no longer makes sense.
Quick Checks a Homeowner Can Try Before Calling
These fast checks often turn warm air into real cooling without tools, especially during heat spikes across 91206 and 91208.
- Confirm the thermostat is set to Cool, not Fan, and drop the setpoint by 3 to 5 degrees.
- Check the filter size and condition. Replace if dirty. Do not run without a filter.
- Walk to the outdoor condenser near the side yard or balcony. Make sure the fan runs and the coil is clear of debris.
- Open all supply registers and confirm returns are not blocked by furniture or drapes.
- Flip the outdoor disconnect off for two minutes, then on. If the compressor restarts and cools, call to test the capacitor and contactor.
When to Shut It Down and Call Right Away
Some symptoms risk major damage or water intrusion in Glendale’s hillside homes and should not wait.
- Ice on the refrigerant lines or the air handler cabinet.
- Acrid or electrical smells from the outdoor unit or breaker trips.
- Water around the indoor unit or a full drain pan alarm.
- Grinding or squealing noises from the blower or outdoor fan.
- Short cycling every 2 to 5 minutes during the hottest hours.
Engineering Details That Matter on a 100-Degree Day
A few field numbers help frame decisions. Glendale attic temperatures commonly run 50 to 60 degrees above outdoor ambient in midafternoon. With 100 outside, that means 150 to 160 in the attic over Verdugo Woodlands or Montecito Park homes. Every uninsulated duct foot in that attic adds a load. Seal and insulate ducts to R-8 and keep runs short. Static pressure above 0.7 in. W.c. On residential air handlers chokes blower capacity. Reducing static by 0.2 in. W.c. Often improves delivered CFM by 10 to 20 percent on variable speed blowers.
For charge verification, subcooling and superheat are king. On a TXV system, hold subcooling to manufacturer spec adjusted for high ambient. On a fixed orifice, set superheat based on indoor wet bulb and outdoor dry bulb. Glendale dry air means lower indoor wet bulb than coastal LA, so watch charts closely. Overcharge at high ambient sends head pressure into a runaway zone. Undercharge invites icing and compressor overheating. A clean condenser coil can drop head pressure by 50 to 100 psi on a hot day, which trims compressor amps and restores capacity.
For heat pumps, the reversing valve coil must energize correctly. Field tests confirm 24 volts at the coil, magnetism at the valve, and proper line temperature flips between modes. If the valve bleeds, measured subcooling and superheat refuse to settle, and vent temperatures hover near room temp. Replacement requires recovery, valve swap with nitrogen flow during brazing, new liquid line drier, deep vacuum below 500 microns, and precise recharge.
Mini-Split Warm Air Cases Across Glendale
Many hillside remodels in Adams Hill and Chevy Chase Canyon use ductless mini-splits. When a head blows warm air under load, the common culprits are dirty coils, low charge at a flare, fan wheel buildup, or mode errors. Indoor units that were never deep-cleaned develop biofilm. This cuts coil heat exchange and makes “cool” air feel warm. A proper deep clean means isolating boards, pulling the blower wheel, and washing the coil and drain pan, not just a surface spray. Outdoor units facing prevailing Santa Ana winds pack their condenser fins with dust. A careful rinse from inside out restores airflow.
Flare leaks show oil stains at fittings. Correct torque and proper flare geometry matter. Techs use a torque wrench, deburr tubing, and apply a small amount of refrigerant-safe assembly compound to prevent microleaks. After repair, nitrogen testing and evacuation are required. Many Mitsubishi Electric and Daikin systems allow field charge checks via service apps and board LEDs. Use them. Guessing charge on inverters wastes time.
Title 24, SEER2, and Practical Glendale Choices
Repairs should respect California Title 24 and SEER2 standards. Replacing a failed condenser fan motor with a mismatched speed or lower efficiency part may “work,” but it pushes head pressure and bills up. Proper component matching maintains rated performance and avoids nuisance trips during Glendale heat spikes. When repair costs pile up, upgrading to a variable speed heat pump or a high-SEER2 central air unit from Carrier, Trane, Lennox, or Daikin makes sense. Variable speed systems hold setpoint in 100-degree heat with lower noise and better filtration. For wildfire seasons, a well-sized return with MERV 13 capability across larger filter area keeps air clean without choking the blower. Green Planet designs to these specs and commissions systems with measured airflow and documented charge.
Glendale Zip Codes, Landmarks, and Why Proximity Matters
Response time saves systems during heatwaves. Crews near the Americana at Brand and Glendale Galleria reach 91203 and 91204 fast. Rossmoyne and 91207 see frequent attic unit issues, often during late afternoon peaks. 91206 and 91208 stretch into the Verdugo Mountains, where outdoor units collect windblown debris and need deeper condenser cleaning to maintain SEER2 efficiency. The Glendale Central Library and Alex Theatre districts include older mixed-use buildings with package units on rooftops. Those units run hotter and need strict maintenance on contactors and capacitors. Forest Lawn Memorial Park proximity sees open hillsides that push dust into Riverside Rancho yards. These micro details affect both diagnosis and stocking for same-day Glendale ac repair.
Brands, Parts, and Stock That Cut Downtime
Warm air in 100-degree weather demands fast parts access. Green Planet service trucks in Glendale stock universal start capacitors, contactors, fan motors for common tonnages, TXV kits for frequent models, condensate safety switches, and high-quality air filters in MERV 11 to MERV 13. OEM parts are pulled when warranty or design requires it. The team services Carrier, Lennox, Trane, Goodman, Rheem, York, American Standard, and supports high-efficiency systems from Daikin, Mitsubishi Electric Mr. Slim, Fujitsu, Bosch, and Honeywell Home controls. Factory training reduces callbacks and protects equipment value. That is vital for Glendale properties where roof access is tough and return trips waste hours in heat.
True Cost of “It’s Probably Fine” During a Heat Wave
Running an AC that blows warm air can double the damage. A compressor that tries to start against a failed capacitor cooks its windings. A frozen coil that melts floods ceilings in hillside homes. A contactor that chatters under partial voltage pits and arcs, taking out adjacent wires. Glendale power grids run hot on 100-degree days. Voltage sags make marginal components fail. A timely repair often costs far less than a compressor replacement and ceiling repair. When symptoms show, shutting down and scheduling a diagnostic protects the system.
Seasonal Maintenance That Prevents Warm Air Emergencies
Preventive HVAC maintenance in Glendale is not fluff. It addresses the exact failure points that lead to warm air calls. A spring or early summer precision tune-up inspects capacitors for value drift, cleans outdoor coils, measures static pressure, verifies blower speeds, clears condensate lines, checks TXV operation, and confirms charge under load. A mid-season check is smart during heavy smoke years, especially near Montrose and the Verdugo foothills. Green Planet’s 26-point inspection includes start capacitor testing, contactor inspection, TXV evaluation, condensate line clearing, and a focus on MERV 13 filtration for Valley dust and wildfire smoke. Customers who keep to that schedule report fewer no-cool events during peak heat.
Green Planet offers a Seasonal AC Tune-Up Special timed for Glendale summers. It is set up to catch drift before 100-degree days arrive. The special includes documented readings and photos of any findings so homeowners can make a clear call on repair versus replacement.
Commercial Corridors and Package Unit Warm Air Calls
Along Brand Boulevard and near the Glendale Galleria, many low-rise buildings use rooftop package units. Warm air in those spaces often traces back to dirty condenser sections, failed economizer dampers stuck in a hot position, or blower belt slippage. On 100-degree days, economizers should be closed, not pulling in 110-degree roof air. Technicians check damper positions, verify belt tension or convert to direct drive when warranted, and confirm charge and coil condition. These fixes restore cooling in boutiques and cafes that rely on steady comfort for customers.
Case Snapshots From Glendale Blocks
Rossmoyne, 91207: A Lennox 3-ton split blew warm during a 102-degree afternoon. Outdoor fan ran, compressor silent. Capacitor measured 7 µF on a 45 µF leg. Replaced with OEM, verified amp draw and subcooling, restored 20-degree split.
Chevy Chase Canyon, 91206: Mitsubishi Electric heat pump showed neutral air. Reversing valve failed to shift. Confirmed 24 volts at coil, mechanical stick found. Replaced valve, pulled to 350 microns, weighed in factory charge. System cooled and held.
Riverside Rancho, 91201: Goodman condenser with clogged coil from dust after Santa Ana winds. Head pressure at 425 psi. Coil cleaned inside out, contactor replaced due to pitting. Head pressure dropped to 300 psi at 100-degree ambient, strong vent delta returned.
Near the Americana at Brand, 91210: Restaurant package unit pulled hot roof air through a failed economizer. Damper repaired, charge checked, belts replaced. Dining room cooled within an hour.
Why Local Matters for HVAC Repair Glendale
Local knowledge trims hours off diagnostics. Knowing that attic accesses in Adams Hill are narrow helps plan which vacuum pump and coil-clean gear to bring. Expecting smoke load after a Verdugo Mountains brush fire changes filter choices. Understanding that Glendale power sags occur late afternoon leads techs to check LRA and capacitor margins first. A company that spends each week around the Glendale Central Library, Alex Theatre, Brand Park, and Forest Lawn Memorial Park brings that context to every call.
Clear Signals That It Is Time To Replace, Not Repair
Warm air during heat spikes can reveal end-of-life. If a compressor is drawing locked rotor amps repeatedly, oil stains dot the coil, and the system uses an obsolete refrigerant, repair dollars may chase diminishing returns. Homes near Glenoaks Canyon with 25-year-old ductwork often gain more from a modern variable speed heat pump and sealed, insulated ducts. Title 24 requires duct testing on change-outs. SEER2-rated systems with proper commissioning drop bills across 91203 and 91204 apartments and hit comfort levels that older gear cannot match. Green Planet provides free estimates on new installations and explains options from Carrier, Trane, Lennox, Daikin, and Mitsubishi Electric in plain terms. The goal is simple: steady, cool air on a 100-degree day without drama.
Service Coverage Beyond Glendale
Systems do not respect city lines. The same warm-air failures show up in Burbank, Pasadena, La Cañada Flintridge, Eagle Rock, Los Feliz, Atwater Village, and Montrose. Crews move across these areas daily. The climate map stays similar, but duct traditions and housing stock vary. Glendale’s knowledge transfers well to these neighbors, which keeps first-visit fix rates high.
What to Expect From a Green Planet Glendale AC Repair Visit
Expect a licensed, bonded CSLB contractor with EPA certified technicians and Google Guaranteed backing. Expect upfront pricing before work begins. Expect factory-trained care for Carrier, Lennox, Trane, Goodman, Rheem, York, American Standard, Daikin, Mitsubishi Electric, Fujitsu, Bosch, and Honeywell Home. Expect that trucks carry universal start capacitors and contactors so most no-cool calls close the same day. Expect documentation that aligns with Title 24 and protects SEER2 performance. That is the standard Glendale homeowners deserve in 100-degree heat.
Ready for Fast Relief in Glendale, CA
Warm air through the vents during a hot afternoon is not a mystery. It is a sign. In Glendale, CA, the causes are familiar and fixable. A blown capacitor, a dirty condenser coil, a frozen evaporator from starved airflow, a clogged condensate line, a short cycling thermostat, a refrigerant leak, or a stuck reversing valve cover most calls. Each has a straight test and a clean fix. The difference is speed and standards. That is where a local team helps.
Green Planet Heating and Air is locally owned and operated, licensed and bonded, and an Energy Star Partner. The company provides 24/7 emergency service, precision tune-ups, and free estimates on new installs. For homeowners through 91201, 91202, 91203, 91204, 91205, 91206, 91207, 91208, and 91210, the path back to cool air is simple. Call for HVAC repair Glendale or Glendale ac repair, schedule a diagnostic, and get the system cooling again with documented readings and clear options.
Book Now: Get Cool Air Back On Today
Schedule your repair now with Green Planet Heating and Air. EPA certified technicians arrive from near the Americana at Brand for fast Glendale response. Ask about the Seasonal AC Tune-Up Special to prevent blown capacitors, frozen coils, and clogged condensate lines before the next heat wave. Expect upfront pricing, CSLB compliance, SEER2-minded repairs, and local care from the Verdugo Mountains to the Atwater Village border.
![]()
Green Planet Heating and Air serves as the premier HVAC contractor in Burbank, CA, providing high-efficiency climate control for the San Fernando Valley. Our technicians specialize in California Title 24 compliant AC repair, furnace replacement, and precision heat pump installations. Whether you are navigating a cooling emergency near the Media District or upgrading indoor air quality in Glendale or Pasadena, our local team delivers EPA-certified expertise. With a focus on energy-saving residential and commercial solutions, Green Planet Heating and Air is the definitive choice for HVAC repair near me in Los Angeles County.
Green Planet Heating and Air
2219 W. Olive Ave. Ste #227
Burbank, CA 91506
License: CSLB #894993
Phone: (818) 383-6516
Email: [email protected]
Official Website: greenplanet-hvac.com
Operational Hours:
Mon-Thu: 8:00 AM - 7:00 PM
Fri: 8:00 AM - 5:00 PM
Sat: Closed (Emergency Dispatch Available)
Sun: 9:00 AM - 3:00 PM
Connect & Review: Facebook | Instagram | Write a Review
Service Area Map: View Our Burbank Location