Five Peugeot Keys Lessons From The Pros

Peugeot 208 Key Replacement

Peugeot 208 key replacement is best left to experienced auto locksmiths who have the appropriate equipment and technical knowledge. They can design and program keys more quickly and at a lower cost than dealers.

If your key fob has stopped locking or unlocking your doors it could be due to a dead battery in the coin. However, there are other reasons that the key may be malfunctioning.

Dead Coin Battery

A dead coin battery can prevent your Peugeot 208 from locking or unlocking and won't start the engine. If this is the case, you'll have to apply the backup starting technique which is explained in the owner's manual for your vehicle.

The spark plugs might also be worn out. The spark plugs are responsible for igniting the fuel that ignites the engine. They are only able to last for a short time. If they aren't used enough they will eventually fail.

There is a simple solution to this problem. The best option is to determine the voltage of your car battery with a multimeter. If it's below 11.5 Volts and you are not satisfied, then it is time to replace it. It is also necessary to clean the contacts of the battery in the event that it is damaged by corrosion. This can be accomplished by removing the rubber covers from the two terminals of the battery, and then using a wirebrush to eliminate any damaged parts of the battery. It is then time to reconnect the cables to the positive and negative poles.

Water Damage

If your 208 will not start and the battery has not failed, you should check the spark plugs. It could be that they're overly dirty, causing them not to spark. The spark plugs can be cleaned in the workshop.

Peugeot automobiles use a key with a transponder compatible with the immobiliser. This makes sure that only the correct key can turn the engine. If the chip in the Peugeot key is damaged then it won't send the correct signal to the vehicle.

This is a common problem that is caused by water damage. This is a typical issue in colder climates where the vehicle is exposed to snow or rain. If this is the case, you should get in touch with a reputable locksmith who will have all of the tools and equipment needed to change the key's programming. They also have the most up-to-date technology and the machinery needed to make the Peugeot 208 smart key. The process should take no more than 15 minutes.

Contacts with the battery may be damaged.

Peugeot changed from the old carbon encased transponder chips and introduced a new type of chip that incorporates electronic components within circuit boards. The new system is great in its initial state, but the circuit boards wear out over time and stop working properly.

This could prevent the immobiliser chip from activating and causing your car to not start. Contact an Peugeot specialist or a locksmith if this is the case.

Another issue that is common is when the battery in the key fob is dying, this causes the blade of the key to stop getting into the lock. A locksmith in your car can replace the battery and cut a new blade for you, it's typically a quick fix.

Faulty Receiver Module

It could be that the receiver module has a problem If your Peugeot key fob fails to function after being dropped on the floor, exposed to a stormy rainstorm, or accidentally washed. The receiver is responsible for sending radio frequency signals to an on-board computer that controls the central locking system inside your Peugeot vehicle.

The key fob itself is fitted with rubber seals that prevent water from getting to the chip inside. The chip can be damaged by water if it is exposed to water for a long time. Submerging the key fob into sea water at the beach or throwing it into the pool can be particularly damaging due to the high salt content.

The module must be replaced if your Peugeot spare key is no longer working. This is only done by a Peugeot specialist or a professional auto locksmith. Peugeot keys, unlike other cars, are protected by an immobilizer system. This requires the proper coding to start the car. This is why you must choose a reputable Peugeot locksmith to handle the task of creating and programming an appropriate replacement.

Computer with a problem on board

The on-board computer of your Peugeot is responsible for many of the systems inside your car, including power windows and airbags. When something goes wrong in these systems, it'll typically display a code that identifies the issue. This code is stored inside the system and stays there until the issue is fixed. Usually, g28carkeys.co.uk will mean the on-board computer being replaced.

One of the main causes of the light turning on is the loose or corroded connections within the airbag sensor. This could be due to wear and tear, aging, exposure to moisture and salt. It is imperative to have this issue resolved as soon as possible, as an airbag that is not functioning properly could be dangerous in the event of an accident.

If your Peugeot is showing a card that is not being detected error, then the battery in the key fob could be weak or dead. This prevents the key fob from sending a signal to disable your vehicle's immobilizer. You can test this by pressing the unlock button on the key fob, then attempting to start your car. If this fails it is because the battery of the key has to be replaced.

Edit Report
Pub: 29 Jun 2024 14:59 UTC
Views: 7