12 Facts About Patio Door Lock Repair That Will Inspire You To Look More Discerning Around The Cooler. Cooler

Patio Door Lock Repairs

Over time, patio doors go through wear and tear which can result in locks that fail. Fortunately, there are patio door repairs near me and effective ways to restore your uPVC patio door's security.

These easy fixes will make your home safer no matter if you adjust the lock or clean the locking mechanism.

Clean the Lock

While patio doors are a great way to let in the outside and keep the elements out but they can also pose a security risk when your lock isn't functioning as it should. Over time, wear and tear, cold and hot weather dirt, and other debris can cause your patio door lock to become difficult to operate. With a little attention, you can make sure that the lock on your patio door always functions properly.

To begin with, it's crucial to clean the lock of your patio door and all of its moving parts. This will help flush out any accumulated grime and coatings that may be preventing the lock from working in the way it should. Begin by wiping the moving parts of your patio door's lock using a damp cloth. then make use of a scouring pad, or a rough damp cloth to scrub any difficult-to-access parts of the door and frame that are coated with dirt. Then, wipe the entire lock with dry cloth to get rid of any remaining dampness, and allow it to air dry before using it again.

If your patio door is equipped with pin-tumbler latches, you can lubricate it by applying powdered Graphite on the key. You can also apply a Teflon oil like WD-40 Multi Use Product. This type of lubricant is easy to apply and it won't disintegrate with time. If you're unable find the right lubricant to use with your lock, apply a pencil that has a larger tip. Insert the pencil into the lock and jiggle it around to spread the graphite.

Regular maintenance is also necessary to keep the tracks of sliding patio doors free of dust, dirt and debris. These tracks are especially susceptible to snow and ice, which could cause them to become stuck or slack and make it difficult for your patio doors to open and close.

The sliding rails of the patio door track and rollers can be cleaned by removing any damaged or dirty weather stripping and cleaning them before replacing it. The same can be done for rollers on patio doors, which can be cleaned and then sprayed with a non-stick lubricant that will allow them to move freely.

Lubricate the Moving Parts

uPVC French Doors, like sliding patios, operate by using 3 to 4 or sometimes, 5 points locking mechanisms. These include the lock cylinder and handle which is operated by the key. These doors also need maintenance, and specifically lubrication of the moving parts. This can be done with an oil that is thin (never WD40) and is recommended to be done at least once per year.

If the hinges aren't causing the problem, it could be that the door is misaligned. It could be rubbing or catching against the strike plate's hole in the frame. Remove the strike plate, and employ a sharp tool expand its mortise. This lets the latch sit properly in the hole and prevents rubbing or catching on the frame.

Take a measurement of the diameter of the cylinder using an object of wood or a book that is able to fit into the space above the adjustment screw. The outer dimension is measured from the outside of door to the center of cylinder. The inner dimension is measured from the center adjustment screw to the end cylinder.

Check the width of the lock.

If your patio door latch isn't able to turn, even after oiling and cleaning it could be because it is not aligned with the strike plate. Examine if the door is balanced and whether the hinge screws are tight however, in many instances, moving the strike plate up or down could fix the problem.

Most of the time, the issue occurs when the strike of the lock is too small for the latch to engage. In this instance, you can widen the opening using the hammer and chisel. Then, test the latch to ensure that it does not rub against the jamb frame of the door or fall the frame.

Before you purchase a replacement lock, it is important to determine the mortise type of lock you have. This can be done by looking at the faceplate and noting whether it is square or round. Then, look at the screw holes on the existing lock and note the size of each. This will help you to locate a replacement lock that is the exact same width and fits into your existing hole.

You'll need to locate the mortise lock, and then examine it for any bends, scratches or other damage that need to be repaired. A badly bent or damaged latch is more likely than one that's frequently used to break. Replace the lock if it displays indications of damage.

Once you've inspected the lock and identified which kind of replacement you require, it's time to start working on the actual repair. Remove the handle and spindle from the patio door, and then insert the new one. Start by installing the inside handle. Align it with the spindle and then secure it in position using two bolts or screws. Install the exterior handle following the interior handle. Once you have completed these steps, test the handles to make sure they are able to open and close easily and that the latch works properly with the strikeplate.

Check the door's Strike

The strike plate and door latch are two pieces which work together to lock the door. If they are not aligned properly and the latch isn't latching the door shut correctly. Fortunately, the issue is usually easy to correct.

Check the holes for receiving of the strike plate to ensure they are free of obstructions, such as dirt or plastic plugs. Release the screws that hold the strike plate. This will allow it to move vertically, but it will not be able to separate from the frame. Adjust the strike plate so that it aligns its receiving holes with the latch hooks of the door latch. Once the strike plate is adjusted, tighten the screws and test the door to see whether it locks smoothly after the new adjustment.

Door strike plates can be difficult to access for homeowners who have sliding patio doors, but they're crucial to lock and unlock your door. The metal plates are situated on the top and bottom jambs of the door, which are where they help support the latch. The door latch slides into this strike plate and creates a seal. If the strike plate is damaged or rusted, or if it is not properly installed the latch may not be able to lock the door properly.

The most common reason for a patio door lock to stick or not close is a misalignment between the latch and the strike plate. The easiest way to check for this is with the "lipstick test." Rub some lipstick on the edge of the deadbolt and put masking tape on it. When you close the door the lipstick will leave an impression on the tape that will show you exactly where the latch connects to the strike plate. If the mark is too low or high it is possible to adjust the strike plate.

If your patio door locks for sliding aren't working correctly, they can keep your home safe from burglars. It is imperative to repair the issue as soon as possible. Follow these easy steps to repair your patio door lock and restore its function.

Edit
Pub: 19 May 2024 12:24 UTC
Views: 5