7 Things About Fiat 500 Replacement Key Cost You'll Kick Yourself For Not Knowing

Fiat 500 Replacement Key Fob

If your remote key fob isn't functioning, it could be time to replace the battery. However, if you replace the battery but it is still not working it is likely to be elsewhere.

United Locksmith specializes in the creation of new keys for classic automobiles. We have the tools and components needed for this service.

Dead Coin Battery

A dead battery is the most common cause of your Fiat 500 keyfob not locking or unlocking the doors. The key fob has an internal battery called a coin cell that will drain quickly in the event that it is not used often enough. If your remote started to show signs of weakening such as a loss of range and then completely stopped working The battery is probably dead.

The battery in the key fob is held in place by metal retaining clips. If the clips are not secure, they could cause contact problems that will prevent your remote from receiving power. Using a small flathead screwdriver, push the clip that holds the retaining pin open to take out the battery, and replace it with a brand new one. Make sure fiat key replacement use a replacement battery with the same type of voltage, dimensions, and specification as the original battery.

Exposure to water can cause the key fob to corrode, or even become damaged. Even a brief shower in soapy water can cause damage to the electronic chip inside. It is best to keep your key fob in a dry location.

Water Damage

If your key fob isn't operating properly, it could be due to water damage. The rubber seals on key fobs protect them from getting damaged by a slight splash or drizzle of water. However, it is important to keep the keys of your car away from the washing machine, ocean, and even the pool.

The key fob contains an electronic chip that sends an electronic message to the immobilizer system of your vehicle. This is the reason why your 500 can start or lock, but when the chip becomes wet, it can no longer function.

You can try cleaning the inside of your key fob's electronics with isopropyl alcohol or an electronic cleaner to see whether they're still in good condition. However, it's recommended to purchase a replacement from a dealer instead of trying to repair a key fob that is submerged in salt water.

A replacement fob could cost you a bit however, it's cheaper than having to have your Fiat 500 towed to a dealership and fixed there! Additionally, you can do it yourself with only a few steps. Be sure to have the correct battery type before you attempt to open your keyfob. You can find step-bystep instructions for any car keyfob on the internet.

Faulty Chip

The chip that is contained in the key fob communicates with the vehicle's immobiliser to ensure that the vehicle is capable of starting when the correct key is inserted. If the chip is damaged or corrupted in any way it will not start.

Damage to the water or a dead battery are the most common causes of a faulty chip. It is best to hand over the work to a professional locksmith who can repair the chip in a short time and at a an affordable cost.

If your key fob stops functioning after exposure to clean tap water or rain, take off the battery and clean the electronic component with a paper towel to ensure that it is completely dry before putting it back in. If the key fob will not work, there is the possibility that it's an issue with the component and requires to be replaced.

Some people will go to their dealer when in need of a new Fiat key fob, however this can be a very costly option. United Locksmith is the best choice if you want your Fiat keyfob fixed at a reasonable cost. We have the tools and experience needed to repair your Fiat key fob in a timely and professional manner.

Faulty Receiver Module

Fiat key fobs send signals up 50 feet away to the vehicle, which can unlock and lock the doors (and start the vehicle for those with automatic transmissions). There are many reasons why a fob could stop working. This includes a dead coin-battery water damage, worn out buttons an issue with the receiver, signal interference or an issue with the chip.

If the fob was in a pocket which has suffered severe trauma (such as being dropped on the floor or washed in the washer) the fob may not be able to communicate with the Body Control Module (BCM) of the vehicle. The BCM is a security device which will only accept signals from genuine original keys.

If this is the case, you will require replacing your fob. A professional locksmith can take care of all aspects of the replacement procedure as well as programming a new one for your 500. They can even offer a clone fob that works just like the original (and costs just one-third of what it would cost).

Edit Report
Pub: 25 Apr 2024 03:41 UTC
Views: 33