smartctl 7.5 2025-04-30 r5714 [x86_64-linux-7.0.11-arch1-1] (local build)
Copyright (C) 2002-25, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Apacer AS340/350 SSDs
Device Model: Apacer AS350 512GB
Serial Number: BF3307581DF900246886
LU WWN Device Id: 5 dc663a 581d3c466
Firmware Version: AP202PS0
User Capacity: 512,110,190,592 bytes [512 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: Solid State Device
Form Factor: 2.5 inches
TRIM Command: Available
Device is: In smartctl database 7.5/5706
ATA Version is: ACS-4 (minor revision not indicated)
SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Fri Jun 5 15:53:51 2026 MSK
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 720) seconds.
Offline data collection
capabilities: (0x79) SMART execute Offline immediate.
No Auto Offline data collection support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 3) minutes.
Extended self-test routine
recommended polling time: ( 30) minutes.
Conveyance self-test routine
recommended polling time: ( 10) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 1363
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 711
163 Max_Erase_Count 0x0032 100 100 000 Old_age Always - 16
164 Average_Erase_Count 0x0032 100 100 000 Old_age Always - 12
166 Later_Bad_Block_Count 0x0032 100 100 000 Old_age Always - 0
167 SSD_Protect_Mode 0x0032 100 100 000 Old_age Always - 0
168 SATA_PHY_Error_Count 0x0032 100 100 000 Old_age Always - 0
171 Program_Fail_Count 0x0032 100 100 000 Old_age Always - 0
172 Erase_Fail_Count 0x0032 100 100 000 Old_age Always - 0
175 Bad_Cluster_Table_Count 0x0032 100 100 000 Old_age Always - 0
192 Unexpect_Power_Loss_Ct 0x0032 100 100 000 Old_age Always - 126
194 Temperature_Celsius 0x0022 067 062 025 Old_age Always - 33 (Min/Max 33/38)
231 Lifetime_Left 0x0012 100 100 000 Old_age Always - 100
241 Total_LBAs_Written 0x0032 100 100 000 Old_age Always - 15501097792
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
The above only provides legacy SMART information - try 'smartctl -x' for more