How To Outsmart Your Boss With Repairs To Upvc Windows

Repairs to uPVC Windows

uPVC windows are a fantastic option for modern homes. They are durable, long-lasting and easy to maintain. As opposed to aluminium and timber they do not rust or rot.

Cleaning and lubricating regularly UPVC windows and doors is vital. This will reduce repair costs as well as improve energy efficiency.

1. Broken Glass


The broken glass in your windows can cause serious damage to your home, and could even be fatal. It is important to take the time to ensure that you're doing all you can to keep your windows in good repair.

Single-pane windows are relatively easy to replace, and they typically fit into frames of the past easily. If you have double-paned windows that are held together by internal beading, it will be difficult to remove and replace the old panes. In window repair near me is essential to purchase plastic spacers to help the new pane fit into the window frame.

Wearing eye protection and heavy gloves is a must when you are planning to remove the glass by yourself. It is also recommended to lay down a drop cloth before you begin working on the window panes to ensure that any shards fall onto the fabric and not onto the floor, where they could be trampled under.

It's a good idea to cover the gap with tape after the glass has been removed. This will keep water and drafts from entering your property until a professional comes out to fix the window. It also acts as an obstruction to prevent criminals from getting into your home. If the gap between the door and the window is significant, you may want to use an alarm system that includes a window. This will provide the best of both.

2. Sagging

Upvc windows and doors are a low-cost energy efficient, durable and long-lasting alternative to timber windows made of sash. As time passes, they may be affected by a variety of issues, including sliding. A window that isn't properly aligned can cause problems with light, draughts, and even security. If you notice that your uPVC window is beginning to sag it's important to act quickly to stop the issue from getting worse.

To fix a window that is sagging you can try repositioning the hinges. First, you'll need to unblock the windows so you can access the frame. Then, remove both the hinges at the top and bottom using a screwdriver and adjust the hinges clockwise or counter-clockwise. Close your window to check the fit after you've relocated your hinges. If you are happy with the fit of your window, you can tighten screws to keep them in the right position.

If you can't reposition the hinges, you might need to replace the seal. Rubber seals may dry out and lose their elasticity with time, leading them to lose their tightness. If this happens, it's important to replace the seal as fast as possible so that your uPVC windows are waterproof and secure from draughts.

uPVC handles may also loosen up. The majority of the time it is due to screws that have come loose over time. However, it could be due to the fact that the handle mechanism has been worn out. Luckily, it's not difficult to fix the handle of a window that is loose yourself. First, you'll need to close the window and perform a test fitting. The corners of the sash need to align with the casing joint. If it isn't, you can use a screwdriver or a wrench to loosen the handle and then reverse the mechanism back into its original position.

3. Water Leaks

It is essential to take action if get up each morning to find mouldy walls and wet floors. The leaks of water through windows could cause structural damage to your home, and impact your ability to regulate the temperature in your home. Most often, uPVC window leaks are caused by a damaged or missing sealant.

This is a simple fix that can be completed by any DIYer who has the ability. Depending on how serious the problem is, the old caulking may have to be removed. It is crucial to keep in mind that when it is about uPVC window repairs you should not be tempted to apply too much caulk and then make the area harder to clean and can reduce your energy efficiency.

Verify that the drainage holes are free of debris inside them and ensure that the sill pan has been angled correctly to drain away from the window. In more serious situations, you may need to think about replacing the window.

Moldy sills and rotten ones are also signs of water leakage. The mold thrives in damp environments and can quickly spread across the home.

It is also important to note that if the leak originates from the glass in your double glazed windows, it's more likely to be an issue with the glass seal rather than the frame or sliding. A uPVC specialist can easily solve this issue by replacing the glass seal. This will restore the full insulation of your windows.

4. Faulty Hinges

If your uPVC windows are brittle to open, or loose and open with a breeze it could be hinges that are at fault. They can be easily repaired by any skilled DIYer and can be completed in just a few minutes.

Like all mechanical parts hinges will wear out over time. It's easy to change the hinges on a window but it's much simpler if you have someone to help hold the frame.

It is also worth checking that the uPVC hinges are opening and closed in the correct direction. This can be done by looking for the arrow on each hinge, this indicates which way the window should be opened.

The problem can be caused either by opening the window incorrectly or due to a poor installation in the factory. This can often be resolved by sending us a photograph through our website and we will be more than happy to give you suggestions.

It is also important to grease the hinges on a regular basis. This can be accomplished by applying an oil that is light in nature to the hinges, we recommend using a solvent-free lubricant, such as 3-in-one Multi-Purpose Oil. Regular lubrication can make the window easier to open and close. It can also stop corrosion and decrease the chance of sticking. This should be done at least once a year. WD40 and other solvent-based oils are not recommended because they can damage the parts of your uPVC window.

5. Draughts

Draughts in Upvc windows can be caused by various factors. The hinges, also due to wear and tear could become misaligned. This will cause an opening to appear where the sash meets the frame. If they're beyond repair, it may be necessary to have them realigned. Second, the interlock can be misaligned. It is located on the hinge's side and may need to be cleaned. In some instances, it may be necessary to replace these.

The next common reason for draughts are the window seals. These are susceptible to being worn out or damaged over time, and will allow air to escape through these gaps. Replacing these with high-quality weatherstripping can help keep draughts at bay. Another alternative is to replace the upvc window with low-emissivity glass, this will help in regulating indoor temperatures and again will lessen draughts.

Another method of reducing drafts effectively is to use a Draught-excluder. These are usually fabric tubes filled with a filler, which can be hung over your window sill. These will keep your home warm by blocking out cold air.

Your windows made of upvc will remain a great source of insulation and security for your home with regular maintenance and repairs. It is essential to remember that all windows will eventually become worn out, and it could be more cost-effective to simply replace them instead of fixing them. If you are experiencing issues with your window made of upvc it is recommended to speak with a professional immediately.

Edit
Pub: 04 Feb 2024 15:17 UTC
Views: 8