5 Reasons Seat Keys Replacement Is Actually A Positive Thing

Seat Alhambra Key Problems

Seat's jumbo MPV range is among the best in its class when it comes to resale value. With a new model on sale the family MPV jumbo is better.


There are a variety of reasons why the key fob might not function properly, such as a dead coin battery or damage to the receiver module, or signal interference. This article will walk you through the steps to make it work again.

Water Damage

If your key fob for the seat alhambra can withstand a wash cycle or a dip in the ocean or a pool then it's got a waterproof chip. But, seat key fob replacement shouldn't do this often as excessive exposure to water can increase chances of the key fob getting damaged. If the key fob stops working after exposure to clean water from the tap or rain, then just remove the battery, wipe the electronic component with paper towel and let it dry completely before putting the battery back into. In case of exposure to soapy or salty water it is recommended to clean the chip with isopropyl alcohol or an electronic cleaner prior to attempting to insert the battery back in.

Faulty Receiver Module

If you have tried a new button cell battery and the key fob cannot be locked or unlocked, it's likely that the receiver module has discovered a problem. The good news is that it is an easy and inexpensive repair, you can just remove the battery 12 volts for a few minutes (first take off the negative cable then press the horn button multiple times) to remove any remaining electric current, then reconnect it in reverse order e.g. positive first, then negative cable later.

ESP Warning Light - If the ESP symbol is illuminated, this is normal. It is a sign that you're driving on terrain that has poor traction. This could be due to gravel, snow or surface water. If the ESP light is always flashing, it is a sign there is a fault in the system. This can be diagnosed by using an iCarsoft i908 seat OBD code reader kit. It will provide a detailed fault description.

Dead Coin Battery

A dead coin battery is among the most common reasons for the keys for the seat to stop working. The key fob is powered by a small button-cell battery. It should be replaced by a new battery that is the same size, voltage and specifications as the original. If you are replacing the battery, ensure that you remove all metal clips from the back of the key fob. You should also ensure that the contacts are free of corrosion.

If the key fob was exposed to water (such as rain or soapy tap water), it is recommended to remove and clean the chip using an electronic cleaner or isopropyl alcohol before installing a brand new battery. The chip is sensitive to moisture and may be permanently damaged. If the key fob is still not working after replacing the battery, it could be necessary to replace the entire key fob.

Faulty Receiver Module

If your key fob stopped working after replacing the battery, but it didn't function, or stopped working abruptly your receiver module might have experienced a malfunction. The receiver module is responsible for capturing the radio frequency signals sent by your remote key fob, and convert them into electrical signals which are then processed by other modules in your car.

If the receiver module has suffered a malfunction that prevents it from responding to any of the commands received by your remote key fob. In this instance you'll need to go to a dealer to reprogram the key fob, and also a new receiver module.

The key fob comes with rubber seals that prevent water from getting into the chip inside. However, if you submerge your key fob into salty or soapy water, the chips inside may be damaged. You can try cleaning the chip by rub it with isopropyl alcohol or electronic cleaner, however If your key fob isn't working after all this, you'll have to purchase a new one.

If the keys are connected, but the receiver module is faulty, you can try to restart all the electronics that are on board by disconnecting the battery with 12 volts for a couple of minutes. Then, reconnect the battery in reverse order (negative cable first before positive). This will reset all electronic components onboard and bring them back into operation.

A malfunctioning electronic chip

The key fob has a small electronic chip that transmits a message to the receiver module when the key is used. If the signal does not match the one the car has stored the immobilizer will turn off and prevent the vehicle starting. However, if the fob isn't functioning and you cannot reprogram it then it could be due to a malfunctioning chip.

The chip in the key fob may need to be changed to allow it to function again. This can be accomplished by taking the key fob away from its housing and using a needle or pin to touch each metal clip. If these clips are damaged or damaged, you'll have to replace them to allow the remote control to function. Make sure that any replacement batteries have the same voltage, size and specifications as the original.

The Seat Alhambra is a well-designed and popular model but, as with any car it is not without its challenges. issues with certain parts or equipment. For instance some owners have encountered problems with the climate control system, which can be faulty and get stuck in one specific setting. The infotainment systems can also malfunction and cause freezes on the screens.

Edit Report
Pub: 26 Apr 2024 17:48 UTC
Views: 50