5 Seat Keys Replacement Projects For Any Budget

Seat Alhambra Key Problems

Seat's family MPV jumbo is among the best in class in terms of retaining resale value. With a brand new model on sale the family MPV jumbo is better.

There are a myriad of reasons why your key fob might not function properly, including a dead battery or damage to the receiver module, water problems or signal interference. This article will guide you through the steps necessary to fix it.

Water Damage

If your key fob for the seat alhambra survives washing cycles or dip in the ocean or a pool then it is equipped with a waterproof chip. However, don't do it often, as prolonged exposure to water can increase the chance of the key fob getting damaged. If the key fob stops functioning after exposure to clean tap water or rain then simply remove the battery, wipe the electronic component with a paper towel and let it dry completely before putting the battery back in. If the key fob has been exposed to soapy or salty water it is recommended you clean the chip using isopropyl or electronic cleaner.

Faulty Receiver Module

If you've tried an entirely new battery for your button and the key fob isn't locked or unlocking, it's likely that the receiver module has discovered a problem. It's a fairly simple and inexpensive fix. You can disconnect the 12 volt battery for a few minutes (first remove the negative cable, then press the horn several times) to eliminate any remaining power. After that, you can reconnect it in reverse. Positive cable first and then negative.

ESP Warning Light - If the ESP warning light flashes, this is normal and means that the car is travelling through terrain that has traction issues between the road surface and the tyres isn't ideal, such as gravel, snow or a lot of surface water. If seat car key not working warning light continues to be flashing, it means there is a fault within the system and should be diagnosed using a iCarsoft i908 Seat OBD Code Reader, which will give you a specific fault description.

Dead Coin Battery

A dead battery for the coin is one of the most frequent reasons for the keys for the seat to stop working. The key fob is powered by a tiny button-cell battery. Replace it with a brand new battery that has the exact voltage, size and specification as the original. When replacing the battery on the key fob, remove the metal clips and make sure that the contacts on the key fob are clean and corrosion-free.

If the key fob has been exposed to water, such as soapy or rain it is recommended to take the battery off and clean the electronic chip with isopropyl alcohol or a electronic cleaner prior to inserting the new battery. The chip could be permanently damaged by water. If the key fob still isn't working after replacing the battery, it might be necessary to replace the key fob.

Faulty Receiver Module

If your key fob has stopped working after replacing the battery, but it didn't work, or if it suddenly stopped working, your receiver module could have developed a problem. The receiver module is responsible for capturing the radio frequency signals that are sent by your remote key fob, and convert them into electrical signals that are then used by other modules in the car.

If the receiver module has suffered a malfunction, it will not respond to any of the commands sent by your remote key fob. In this case, you will need to go to a dealer to reprogram your key fob and new receiver module.

The key fob is covered with rubber to stop water from entering the electronic chip. If you submerge the key fob into salty or soapy water, it could damage the chip. It is possible to clean the chip by rubbing it with isopropyl alcohol or electronic cleaner, but should your key fob isn't working after all this, you'll have to purchase a replacement.

If the keys have been linked, but the receiver module is not working then you can restart all the electronics on board by disconnecting the battery at 12 volts for few minutes. Then, reconnect the battery in reverse order (negative cable first and then positive). This will reset the onboard electronic and restore their functionality.

Electronic Chip Faulty

The key fob is fitted with a tiny chip that transmits the signal from the key to the receiver module every time the key is used. If the signal does not match the one that the car has stored the immobilizer is disabled and prevent the vehicle starting. If the key fob you purchased does not work and you are unable to reprogram it, this could be because of a malfunctioning microchip.

The chip inside the key fob is not permanent to the device, and might need to be replaced to make it work again. The best method to do this is by removing the key from its housing and using a pin needle to connect with each of the metal clips that hold it. If these clips are damaged or broken, you will need to replace them to allow the remote control to work. Make sure that any replacement batteries are of the same size, voltage, and specification as the original one.

The Seat Alhambra is a well-designed and popular model however, just like any other vehicle, it can sometimes experience issues with particular components or equipment. For example some owners have encountered problems with the climate control system, which can malfunction and cause problems in one specific setting. Additionally, the infotainment feature has also been known to malfunction and freeze screens.

Edit
Pub: 26 Apr 2024 03:06 UTC
Views: 16